PERTANIKA JOURNAL OF SCIENCE AND TECHNOLOGY

This paper investigates the behaviour of partial discharge (PD) in transformer insulation paper based on the Finite Element Method (FEM). The three-dimensional (3D) FEM model consists of conductor and insulation paper, representing part of a transformer’s high voltage winding. The conductor’s width, height, and length used in this study were 2.4 mm, 11.5 mm, and 16 mm. An insulation paper thickness of 1 mm was modelled around the conductor. An internal cavity with a diameter of 0.5 mm cavity was introduced within the insulation paper. This study introduced two locations of the spherical cavities at the centre and left corner of the insulation paper: Location 1 (L1) and Location 2 (L2). An AC voltage of 33 kV, 50 Hz, was applied to the conductor while the bottom of the insulation paper was grounded. The model was used to study the electric field distribution within the insulation paper and its effect on PD current and charge magnitude. The influence of cavity location on the charge magnitude was also examined. It is found that the electric field distribution is influenced by the conductor configuration as well as the location of the cavity. The electric field in the cavity is the highest at L1 compared to L2. The first PD occurs faster for the cavity with a high electric field. Due to the PD occurrence at the same inception field, the real PD current and charge magnitude is similar at different locations. The apparent PD current and charge magnitude induced at the ground electrode is slightly higher at L1 than at L2.

• Anagha, E. R., Joseph, J., & Sindhu, T. K. (2018). A finite element method based approach for modeling of partial discharges in HVDC cables. In 2018 Electrical Insulation Conference (EIC) (pp. 533-537). IEEE Publishing. https://doi.org/10.1109/EIC.2018.8481089

• Borghei, M., Ghassemi, M., Rodriguez-Serna, J. M., & Albarracin-Sanchez, R. (2021). A finite element analysis and an improved induced charge concept for partial discharge modeling. IEEE Transactions on Power Delivery, 36(4), 2570-2581. https://doi.org/10.1109/tpwrd.2020.2991589

• E-CIGRE. (2017). Partial Discharges in Transformers. e-cigre.org. https://e-cigre.org/publication/676-partial-discharges-in-transformers

• Forssén, C., & Edin, H. (2008). Partial discharges in a cavity at variable applied frequency part 2: Measurements and modeling. IEEE Transactions on Dielectrics and Electrical Insulation, 15(6), 1610-1616. https://doi.org/10.1109/TDEI.2008.4712664

• Hussain, M. R., Refaat, S. S., & Abu-Rub, H. (2021). Overview and partial discharge analysis of power transformers: A literature review. IEEE Access, 9, 64587-64605. https://doi.org/10.1109/access.2021.3075288

• Illias, H. A., Chen, G., & Lewin, P. L. (2017). Comparison between three-capacitance, analytical-based and finite element analysis partial discharge models in condition monitoring. IEEE Transactions on Dielectrics and Electrical Insulation, 24(1), 99-109. https://doi.org/10.1109/tdei.2016.005971

• Illias, H. A., Tunio, M. A., Mokhlis, H., Chen, G., & Bakar, A. H. A. (2015a). Determination of partial discharge time lag in void using physical model approach. IEEE Transactions on Dielectrics and Electrical Insulation, 22(1), 463-471. https://doi.org/10.1109/tdei.2014.004618

• Illias, H. A., Tunio, M. A., Mokhlis, H., Chen, G., & Bakar, A. H. A. (2015b). Experiment and modeling of void discharges within dielectric insulation material under impulse voltage. IEEE Transactions on Dielectrics and Electrical Insulation, 22(4), 2252-2260. https://doi.org/10.1109/tdei.2015.004817

• Illias, H. A., Chen, G., & Lewin, P. L. (2012a). Partial discharge within a spherical cavity in a dielectric material as a function of cavity size and material temperature. IET Science, Measurement & Technology, 6(2), 52-62. https://doi.org/10.1049/iet-smt.2011.0091

• Illias, H. A., Jian, L. T., Bakar, A. H. A., & Mokhlis, H. (2012b). Partial discharge simulation under various applied voltage waveforms. In 2012 IEEE International Conference on Power and Energy (PECon), (pp. 967-972). IEEE Publishing. https://doi.org/10.1109/PECon.2012.6450358

• Illias, H. A. (2011). Measurement and simulation of partial discharges within a spherical cavity in a solid dielectric material [Doctoral dissertation]. University of Southampton, UK. https://eprints.soton.ac.uk/194921/

• Illias, H. A., Chen, G., & Lewin, P. L. (2011a). The influence of spherical cavity surface charge distribution on the sequence of partial discharge events. Journal of Physics D: Applied Physics, 44(24), 245202. https://doi.org/10.1088/0022-3727/44/24/245202

• Illias, H. A., Chen, G., & Lewin, P. L. (2011b). Partial discharge behavior within a spherical cavity in a solid dielectric material as a function of frequency and amplitude of the applied voltage. IEEE Transactions on Dielectrics and Electrical Insulation, 18(2), 432-443. https://doi.org/10.1109/TDEI.2011.5739447

• Illias, H. A., Chen, G., & Lewin, P. L. (2011c). Partial discharge behaviour within two spherical cavities in a dielectric material. In 2011 Annual Report Conference on Electrical Insulation and Dielectric Phenomena (pp. 456-459). IEEE Publishing. https://doi.org/10.1109/CEIDP.2011.6232693

• Illias, H. A., Chen, G., & Lewin, P. L. (2010). Comparison of partial discharge measurement and simulation results for spherical cavities within solid dielectric materials as a function of frequency using finite element analysis method. In 2010 IEEE International Symposium on Electrical Insulation (pp. 1-5). IEEE Publishing. https://doi.org/10.1109/ELINSL.2010.5549733

• Illias, H. A., Chen, G., & Lewin, P. L. (2009). Partial discharge measurements for spherical cavities within solid dielectric materials under different stress and cavity conditions In 2009 Annual Report Conference on Electrical Insulation and Dielectric Phenomena (pp. 388-391). IEEE Publishing. https://doi.org/10.1109/CEIDP.2009.5377831

• Joseph, J., Mohan, S., & Krishnan, S. T. (2019). Numerical modelling, simulation and experimental validation of partial discharge in cross‐linked polyethylene cables. IET Science, Measurement & Technology, 13(2), 309-317. https://doi.org/10.1049/iet-smt.2018.5248

• Murthy, A. S., Azis, N., Jasni, J., Othman, M. L., Yousof, M. F. M., & Talib, M. A. (2020). Extraction of winding parameters for 33/11 kV, 30 MVA transformer based on finite element method for frequency response modelling. PLoS One, 15(8), Article e0236409. https://doi.org/10.1371/journal.pone.0236409

• Naidu, M. S., & Kamaraju, V. (2013). High Voltage Engineering. McGraw Hill.

• Niemeyer, L. (1995). A generalized approach to partial discharge modeling. IEEE Transactions on Dielectrics and Electrical Insulation, 2(4), 510-528. https://doi.org/10.1109/94.407017

• Pan, C., Chen, G., Tang, J., & Wu, K. (2019). Numerical modeling of partial discharges in a solid dielectric-bounded cavity: A review. IEEE Transactions on Dielectrics and Electrical Insulation, 26(3), 981-1000. https://doi.org/10.1109/tdei.2019.007945

• Pedersen, A., Crichton, G. C., & McAIIister, I. W. (1995). The functional relation between partial discharges and induced charge. IEEE Transactions on Dielectrics and Electrical Insulation, 2(4), 535-543. https://doi.org/10.1109/94.407019

• Pedersen, A., Crichton, G. C., & McAlIister, I. W. (1991). The theory and measurement of partial discharge transients. IEEE Transactions on Electrical Insulation, 26(3), 487-497. https://doi.org/10.1109/14.85121

• Whitehead, S. (1952). Electrical breakdown of solids. Nature, 170, Article 219. https://doi.org/10.1038/170219a0